Tools/Maintenance

Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.

Help your bearings run smoother and longer with Finish Line's Ceramic Grease. Its special blend of ceramic particles, Teflon and synthetic oils helps lube your bearings and dissipate heat, guaranteeing longer life and better function. Plus, it works great on stems, posts, cables and other threaded assemblies, too. - Optimizes performance and efficiency of bottom brackets, hubs and headset bearings - Use on stems, seat posts, cables and any threaded assemblies - Prevents rusting even when exposed to salt water - Clear and non-staining

Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless forks. Slide on the guide, clamp it down and the hardened-steel cutting slot ensures a perfect cut every time. You can remove as little as 1mm, too.

Park's Spoke Wrench For Shimano Wheel Systems is the right tool for the job. It's made of durable tool steel and features 4.4mm and 3.75mm openings to fit all Shimano Wheel System nipples located at the hub and at the rim. It's vinyl-coated for a great grip, too.

Park Tool's Fork Threading Set is designed for cutting new threads and for chasing existing threads on fork columns that are not chromed. The FTS-1's expandable cutting dies are made from the highest quality high-speed steel for precision cutting and long life. The unique thread guide system used with the FTS-1 is specially designed to allow the metal chips and shavings that result during use to fall completely through the guide, preventing damage to the fork threads and the tool. The FTS-1 includes: • Die handles • 1" x 24 tpi cutting die (Part #606) • 1" cutting guide (Part #610) Accessory dies and guides are also available separately: • 1-1/8" x 26 die (Part #607) • 1-1/8" guide (Part #611) • 1-1/4" x 26 die (Part #608) • 1-1/4" guide (Part #612) Die handles fit all three sizes of dies and guides.

• Essential mechanic tools to properly service and maintain all RockShox products • For RockShox Vivid/Vivid Air rear shocks

- 8mm to 16mm hex wrench adapter for removal of spindle from Cinch non-drive crank arm

Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.

Park's Threadless Star Nut Setter makes it quick and easy to install star-fangled nuts used with 1-inch and 1-1/8-inch threadless headset systems. Using a durable steel driver the TNS-1 sets the star nut to the perfect depth every time.

Park's AWS-7 features a Y-shaped nylon handle with 4 and 5mm Allen wrenches and a T25 Torx wrench. This convenient 3-in-1 tool keeps commonly used wrenches together and offers an excellent grip as well.

Park's Crank and Bottom Bracket Wrench is perfect for working on old-style bottom brackets. The HCW-4 utilizes a 36mm box-end head and a pin spanner for your bottom bracket removal and installation needs.

Park's Dial Indicator Gauge Set mounts to their TS-2 or TS-2.2 Truing Stand (sold separately). The set makes it easy to view and correct a wheel's lateral and radial run-out within a tolerance of .01mm. Compared to going by the gap between the truing stand pointer and rim, having gauges that put a number on the clearance makes wheel truing easier and more accurate.

Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.

Developed for locking the nipple to the spoke during the wheel-building process, preventing the spoke-nipple connection from loosening. - Holds nipples in place but allows for up to 5 adjustments before compound breaks down - Use with light oil for a secure, re-trueable wheel or use by itself for a maximum bond - Developed in conjunction with Loctite - Includes two 10ml bottles

- The HBP-1 is designed to quickly and accurately press bearings into a wide variety of cartridge bearing-type bicycle hubs. - Quick release design for fast tool installation and removal - Includes two bearing presses and precision machined aluminum pilots, bushings, and spacers - Works with more than 20 different cartridge bearing sizes and multiple axle configurations

Park Tool's 238K Caliper Upgrade Kit will upgrade the TS-2 Professional Truing Stand to accept wider wheels and tires to increase the versatility of your TS-2 truiing stand. The set includes left and right caliper fingers, and one pair of the plastic removable tips. NOTE: The 238K will not allow the wide 29er wheels with plus-sized tires to be trued in the older TS-2 stands. Use the upright extensions TS-2EXT.2 to for truing 29er wheels with plus-sized tires.

- Handy tool to have to easily remove your KMC MissingLink. - Easy to handle! - Very comfortable!

A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.

In-bike storage and essential riding tools that can meet the needs of almost any trailside repair. Durable, flexible storage sleeves make for a secure, clean place to stow EnCase System tools or other small items. Fits most mountain bars and most road bars thanks to a storage sleeve with a customizable rubber flap that can be cut to meet your handlebar inner diameter. - 14 functions (spoke wrench; valve core wrench; flat head #3.5; Phillips #2; 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, and 8mm hex; and T10, T25, and T30 Torx) - Magnets & O-rings keep all parts in place - Ball detent swivel head helps access hard-to-reach places - Handle doubles as breaker bar when ball detent swivel head is bent for extra torque - Store in handlebar with a Wolf Tooth EnCase Storage Sleeve (included) - Magnet on bottom end of tool allows for storage on steel bike stands (or refrigerators) - Fits most standard mountain handlebars and most drop bars (except ergonomic drop bars that have hard angles in the drops) - Chain & Tire Plug tool compatible with all bicycle chains including 12-speed - Inserter tool and bacon strips plug holes in tubeless tires - Five strips included; refills available - Hardened steel pin for lifetime durability - Requires 4mm hex for chain tool driver which can be found on the EnCase Hex Bit Wrench - Storage sleeves made of vibration-damping material and snug fit prevents rattling - Durable precision-machined aluminum end caps - Custom fit rubber flap can be trimmed to fit in smaller diameter bars - Bonus storage space—fits a Presta-to-Schrader adapter and valve core or a master link (both sold separately) - Includes Drop Bar Fit Kit to customize fit for larger-diameter road handlebars

Make simple trailside or roadside repairs with this multi-tool that has 14 functions. An 8mm hex head has a 4mm insert to fit each of the eight attached hex bits. With its slim design, this multi-tool can be stowed inside an EnCase System Storage Sleeve to be carried in handlebar ends as it was designed, or a mainstay on any home workbench. - 14 functions (spoke wrench; valve core wrench; flat head #3.5; Phillips #2; 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, and 8mm hex; and T10, T25, and T30 Torx) - Magnets & O-rings keep all parts in place - Ball detent swivel head helps access hard-to-reach places - Handle doubles as breaker bar when ball detent swivel head is bent for extra torque - Store in handlebar with a Wolf Tooth EnCase Storage Sleeve (sold separately) - Magnet on bottom end of tool allows for storage on steel bike stands - Fits all standard mountain handlebars and most drop bars (except being ergonomic drop bars that have hard angles in the drops)

Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.

A bench-mounted version of our popular PCS-10.2 Deluxe Home Mechanic Repair Stand. Features our world-famous cam-actuated micro adjust clamp design, which securely holds bicycles in place while allowing quick installation and removal. - Cam actuated, micro-adjustable clamp allows quick entry and exit and fits 1-inch to 3-inches (25mm–76mm) diameter tubes and seat posts of any shape and material - Narrow clamping jaws (2.7-inch/7cm) fit into tight areas or on short seat posts - 360° infinite clamp rotation allows bike to placed in optimal position for specific repairs - All-steel structure for maximum stiffness and durability - Super strong glass-filled nylon-composite fittings and top tube internals enable smooth rotation and secure positioning - Mounts to any flat surface (mounting bolts not included) Distance from the center of the clamp to the center of the mount is approximately 11 3/4-inch (30cm). Height from bench to center of the clamp axis is approximately 9 7/8-inch (25cm). Weight Limit: The PCS-12.2 Home Mechanic Bench Mount Repair Stand has an 80 lb. (36kg) weight limit, provided the stand is securely mounted with appropriate fasteners to a solid and secure bench surface. The user is responsible for making sure the workbench and the fasteners are capable of handling this amount of weight.

Special tools for building Surly Fat Bike wheels. - 56mm-wide spacer aids in dishing and truing Moonlander offset wheels - 35mm-wide spacer aids in dishing and truing Pugsley offset wheels

- Heavy-duty device that cleans chain in seconds - The kit includes a 75 ml bottle of Drivetrain Cleaner that can be either sprayed over the drivetrain or poured into the top reservoir - Liquid release button ensures the application of the cleaner is quick and easily controlled. - Abrasive cleaning teeth and rotating brush wheels which have 120 contact points cover every part of each chain link for a deep and thorough clean - Excess dirty fluid drops into a second lower reservoir so it’s kept away from the clean chain

Park Tool's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press which is sold separately) BB86, BB90, BB92 and Press Fit bottom brackets from Shimano, Race Face, SRAM and others that use a nominal 24mm-diameter spindle. This tool has a bearing remover that fits inside the bottom bracket shell and into the bearing so the bearings can be tapped out of the frame with a hammer. The set also includes two bushings that you use in conjunction with a bearing press for precision bearing installation (bearing press sold separately).

- For removing/installing cartridge bearings in SRAM X0 hubs and Roam, Rail and Rise wheels

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

- Pedal thread inserts are used to replace damaged threads in cranks

Park's Open Ended Metric Wrench is a special thin wrench with 8 and 10mm openings perfect for adjusting the thin pivot-bolt nuts on sidepull brakes (and other hex nuts on your bicycle). This handy brake tool is made of durable tool steel that's nickel plated for corrosion resistance.

DOT 5.1 Brake Fluid, 16 OZ Bottle. Viscosity-stable across highest range of operating temperatures.